 |
 |
 |
 |
 |
 |
 |
 |
Drainage/Cavity |
|
|
 |
 |
 |
 |
 |
 |
|||
| Mortar Net - 1" | |||
| Mortar
Net™ is placed on top of the flashing inside the cavity where
it catches and suspends mortar droppings above the level of weep
holes and flashing. Dovetail shape prevents the mortar from forming
a continuous dam. The shape of the material, in combination with
90% open plastic mesh configuration, allows water and air to move
rapidly and easily through material to the weeps. Available in:
|
|||
 Product
Data Sheet |
 MSDS
1" |
||
 |
|||
| Mortar Net Green - 2" |  |
||
These
non-woven products are made from polyester fiber bonded with flame
retarded adhesive that contains an antimicrobial to effectively control
the growth of mold, mildew, algae, and fungi on the bonded product.
The products are very permeable to air, water or water vapor due to
the low fiber density of the non-woven structure. The void volume
of these products is approximately 99% with only 1% solidity. They
also have excellent flame retardant properties, and the vertically
held test sample will self extinguish after the flame source is removed.
|
|||
|
Product
Data Sheet |
MSDS
2" |
||
|
|||
| Mortar Net - .4" |
 |
||
| Mortar Net™ is placed on top of the flashing inside the cavity where it catches and suspends mortar droppings above the level of weep holes and flashing. Dovetail shape prevents the mortar from forming a continuous dam. The shape of the material, in combination with 90% open plastic mesh configuration, allows water and air to move rapidly and easily through material to the weeps. Available
in: |
|||
| Product
Data Sheet |
MSDS
.4" |
||
| |
LEED
Letter |
||
| Mortar Break® 1" |   |
||
For
use at all flashing locations, such as cavity, composite, single wythe
and veneer applications. The polymer core geomatrix design allows
moisture to seep down through any mortar droppings and weep out of
the wall through the weep holes. Mortar Break®, used with properly
installed flashing and weep holes along with good mortar application
techniques, will ensure the performance of a well-designed masonry
wall.
|
|||
|
Product
Data Sheet |
MSDS
|
||
| Mortar Break II® |  |
||
Mortar
Break II ® is to be used in conjunction with standard 2"
wide cavity wall construction. Mortar Break II ® is a 1.5"
thick, high density, polypropylene geometric design. The slightly
narrower profile of Mortar Break II ® allows for a better fit
in a 2" cavity and avoids any possibility of mortar bridging
the cavity. It is this bridging of mortar, although not continuous,
that would allow moisture to travel into the interior wythe of a typical
cavity wall.
|
|||
|
Product
Data Sheet |
MSDS
|
||
| |
|||
| Mortar Catch® .4" | |||
| For
use at all flashing locations where wide cavity construction is required.
The polymer core geomatrix design, when shaped in a "U"
configuration on the jobsite, fills the cavity and allows moisture
to weep at both inner wall surfaces. Mortar Catch® used with quality flashing, weep holes and good mortar applying techniques will ensure the performance of a properly designed masonry wall.
|
|||
|
Product
Data Sheet |
MSDS
|
||
| Stone Veneer Drainage |
 |
||
Mortairvent
- .25" Available
in: |
|||
|
Product
Data Sheet |
MSDS
|
||
| Pea Stone |
|
||
| Pea
stone is used for drainage on base of cavity wall. Available in:  50 lb bags |
|||
| Product
Data Sheet |
MSDS
|
||
|
LEED
furnished upon request - Please call 1-800-659-4731 |
|||
| Brick Vents | |||
| "EX" Extruded Vents are desgined with a deep louvered overlaping blade, the blade itself has a storm stop at the rear, with a high waterstop at the rear of vent. Vents are supplied with 18 x 14 aluminum mesh insect screen. "FL"
Extruded Vents make possible simplified installation in existing
walls. Chopped-out hole need not be "finished". An attractive
appearance is assured by flange. |
 EX Series 
FL Series |
||
| Product
Data Sheet |
MSDS - Not Applicable |
||
|
LEED
Letter |
|||
| Back to top | |||
MASONPRO, Inc. 1-800-659-4731
© 2001 - 2010 Masonpro, Inc.