Drainage Mesh

Cavity Drainage Netting:

LogoDT_online
ProNetProNet™ DT – 1″

ProNet™ DT is placed on top of the flashing inside the cavity where it catches and suspends mortar droppings above the level of weep holes and flashing. Dovetail shape prevents the mortar from forming a continuous dam. The shape of the material, in combination with 90% open plastic mesh configuration, allows water and air to move rapidly and easily through material to the weeps.

Available in:

  • 1″ X 10″

Product Data Sheet  SDS LEED shoppingcart_blue Purchase Online
Installation Recommendations


LogoDT_online
ProNe  ProNet™ DT – 2″

These non-woven products are made from polyester fiber bonded with flame retarded adhesive that contains an antimicrobial to effectively control the growth of mold, mildew, algae, and fungi on the bonded product. The products are very permeable to air, water or water vapor due to the low fiber density of the non-woven structure. The void volume of these products is approximately 99% with only 1% solidity. They also have excellent flame retardant properties, and the vertically held test sample will self extinguish after the flame source is removed.

Available in:

  • 2″ X 10″

Product Data Sheet  SDS LEED shoppingcart_blue Purchase Online
Installation Recommendations


LogoDT_online
ProNet ProNet™ DT – .4″

ProNet™ DT is placed on top of the flashing inside the cavity where it catches and suspends mortar droppings above the level of weep holes and flashing. Dovetail shape prevents the mortar from forming a continuous dam. The shape of the material, in combination with 90% open plastic mesh configuration, allows water and air to move rapidly and easily through material to the weeps.

Available in:

  • .4″ X 10″

Product Data Sheet  SDS LEED shoppingcart_blue Purchase Online
Installation Recommendations


Mortar Net
Mortar Net® – 1″

Mortar Net® is placed on top of the flashing inside the cavity where it catches and suspends mortar droppings above the level of weep holes and flashing. Dovetail shape prevents the mortar from forming a continuous dam. The shape of the material, in combination with 90% open plastic mesh configuration, allows water and air to move rapidly and easily through material to the weeps.

Available in:

  • 1″ X 10″

 Product Data Sheet SDS  LEED shoppingcart_blue Purchase Online


Mortar NetMortar Net® – 2″

These non-woven products are made from polyester fiber bonded with flame retarded adhesive that contains an antimicrobial to effectively control the growth of mold, mildew, algae, and fungi on the bonded product. The products are very permeable to air, water or water vapor due to the low fiber density of the non-woven structure. The void volume of these products is approximately 99% with only 1% solidity. They also have excellent flame retardant properties, and the vertically held test sample will self extinguish after the flame source is removed.

Available in:

  • 2″ X 10″

 Product Data Sheet  SDS  LEED shoppingcart_blue Purchase Online


mortarnetlogoMortar NetMortar Net® – .4″

Mortar Net® is placed on top of the flashing inside the cavity where it catches and suspends mortar droppings above the level of weep holes and flashing. Dovetail shape prevents the mortar from forming a continuous dam. The shape of the material, in combination with 90% open plastic mesh configuration, allows water and air to move rapidly and easily through material to the weeps.

Available in:

  • .4″ X 10″

 Product Data Sheet  SDS  LEED shoppingcart_blue Purchase Online


Mortar BreakMortar Break® I – 1″

For use at all flashing locations, such as cavity, composite, single wythe and veneer applications. The polymer core geomatrix design allows moisture to seep down through any mortar droppings and weep out of the wall through the weep holes. Mortar Break®, used with properly installed flashing and weep holes along with good mortar application techniques, will ensure the performance of a well-designed masonry wall.

Available in:

  • 1″ X 10″

 Product Data Sheet AIS/SDS LEED shoppingcart_blue Purchase Online


Mortar Break IIMortar Break® II

Mortar Break II ® is to be used in conjunction with standard 2″ wide cavity wall construction. Mortar Break II ® is a 1.5″ thick, high density, polypropylene geometric design. The slightly narrower profile of Mortar Break II ® allows for a better fit in a 2″ cavity and avoids any possibility of mortar bridging the cavity. It is this bridging of mortar, although not continuous, that would allow moisture to travel into the interior wythe of a typical cavity wall.

Available in:

  • Actual size 1.5″ X 10″

 Product Data Sheet  AIS/SDS LEED  shoppingcart_blue Purchase Online


Mortar CatchMortar Catch® .4″

For use at all flashing locations where wide cavity construction is required. The polymer core geomatrix design, when shaped in a “U” configuration on the jobsite, fills the cavity and allows moisture to weep at both inner wall surfaces. Mortar Catch® used with quality flashing, weep holes and good mortar applying techniques will ensure the performance of a properly designed masonry wall.

Available in:

  • .4″ X 10″

 Product Data Sheet  AIS/SDS LEED

Stone Veneer Drainage:

MortairventMortairvent® – .25″

Creates a drainage/ventilation cavity environment behind natural and manufactured stone veneer walls. The polymer core mesh creates the airspace, while the lighter fabric prevents mortar from seeping into the newly formed cavity.

Available in the following dimensions:

  • Width (less flap) 39 inches
  • Width (with flap) 43 inches
  • Length 61.5 feet
  • (200 square feet)

 Product Data Sheet  AIS/SDS LEED shoppingcart_blue Purchase Online


CavClearLogo
CavClearCavClear®

Cavity air space maintenance and drainage material.

 Product Data Sheet  SDS LEED


Pea StonePea Stone

Pea stone is used for drainage on base of cavity wall.

Available in the following dimensions:

  • 50 lb bags

 Product Data Sheet SDS
LEED furnished upon request – Please call 1-800-659-4731


Extruded Brick VentsBrick Vents

“EX” Extruded Vents are desgined with a deep louvered overlaping blade, the blade itself has a storm stop at the rear, with a high waterstop at the rear of vent. Vents are supplied with 18 x 14 aluminum mesh insect screen.

“FL” Extruded Vents make possible simplified installation in existing walls. Chopped-out hole need not be “finished”. An attractive appearance is assured by flange.
1-1/2″ Deep w/1″ Front Flange

Both “EX” and “FL”:

  • Available in any special size to suit any job design
  • Minimum .125” thickness
  • All blades are 1″ deep, set at 45 degree angles

Finish:

  • Extruded Aluminum to be 6063-T5 alloy
  • 204-R1 Clear Anodized finish standard

 Product Data Sheet LEED